ZTE 320 OLT Settings Config Snippets

LACP

Для агрегации портов на OLT ZTE ZXA10 C320 используется smartgroup, которая должна быть создана и добавлена на порты для работы их как часть одного Port-Channel.

Для создания и корректной работы порты-члены интерфейса smartgroup должны работать в дуплексном режиме (full-duplex) и иметь одинаковую конфигурацию.

Создаем smartgroup

ZXAN(config)#interface smartgroup1 
ZXAN(config-if)# 

Затем указываем режим ее работы в примере trunk с вланом 2000

ZXAN(config-if)#switchport mode trunk 
ZXAN(config-if)#switchport vlan 2000 tag 

Задаем режим балансировки

ZXAN(config-if)#smartgroup load-balance src-dst-mac
ZXA10 С320 поддерживает 6 режимов балансировки: 
src-ip - source IP; 
dst-ip - destination IP;
src-dst-ip - source/destination IPs; 
src-mac - source MAC; 
dst-mac - destination MAC; 
src-dst-mac - source/destination MACs.

Режим по умолчанию source/destination MACs.

Затем, добавляем физические интерфейсы в агрегированный канал

ZXAN(config)#interface gei_1/4/1
ZXAN(config-if)#switchport mode trunk
ZXAN(config-if)#switchport vlan 2000 tag 
ZXAN(config-if)#smartgroup 1 mode active
ZXAN(config-if)#exit
ZXAN(config)#interface gei_1/4/2
ZXAN(config-if)#switchport mode trunk
ZXAN(config-if)#switchport vlan 2000 tag 
ZXAN(config-if)#smartgroup 1 mode active 

Стоит отметить, что атрибуты VLAN порта-участника должны быть соответствовать с атрибутами смарт-группы. В противном случае порт не может быть добавлен в smartgroup.

После этого оба порта (gei_1/4/1 и gei_1/4/2) на карте управления SMXA установленной в 4м порту шасси С320 будут обрабатывать трафик как один физический порт.

ZXAN(config-if)#show lacp internal

Smartgroup:1
Flag *–LOOP is TRUE
Actor     Agg        LACPDUs   Port       Oper   Port    RX           Mux
Port      State      Interval  Priority   Key    State   Machine      Machine
-------------------------------------------------------------------------------
gei_1/4/1 unselected 30         32768    0x104   0x45   port-disabled defaulted
gei_1/4/2 unselected 30         32768    0x104   0x45   port-disabled defaulted

ZXAN(config-if)#

Неотсортированные примеры

Serius(config)#show gpon onu state gpon-olt_1/2/3


OnuIndex               Admin State  OMCC State   O7 State     Phase State
----------------------------------------------------------------------------
gpon-onu_1/2/7:1       enable       disable      unknown      OffLine
gpon-onu_1/2/7:2       enable       enable       operation    working
gpon-onu_1/2/7:3       enable       enable       operation    working
gpon-onu_1/2/7:4       enable       enable       operation    working
gpon-onu_1/2/7:5       enable       disable       operation    DyingGasp
gpon-onu_1/2/7:6       enable       enable       operation    working
gpon-onu_1/2/7:7       enable       enable       operation    working
gpon-onu_1/2/7:8       enable       disable      unknown      LOS
gpon-onu_1/2/7:9       enable       enable       operation    working
gpon-onu_1/2/7:10      enable       enable       operation    working
ONU Number: 8/10


== Check ONT power ==

iSerius(config)#show pon power attenuation gpon-onu_1/2/3:1

           OLT                  ONU              Attenuation
--------------------------------------------------------------------------
 up      Rx :-15.810(dbm)      Tx:2.594(dbm)        18.404(dB)

 down    Tx :5.276(dbm)        Rx:-13.233(dbm)      18.509(dB)


== CHECKING ONT MAC ADDRESS ==

iSerius(config)#show mac gpon onu gpon-onu_1/2/3:1

Total mac address : 5

Mac address      Vlan   Type      Port                         Vc
------------------------------------------------------------------------
807d.3a17.87f2   1000   Dynamic   gpon-onu_1/2/9:25         vport 1
807d.3a46.5dda   1000   Dynamic   gpon-onu_1/2/9:25         vport 1
807d.3a46.60b7   1000   Dynamic   gpon-onu_1/2/9:25         vport 1
a020.a625.225c   1000   Dynamic   gpon-onu_1/2/9:25         vport 1
0488.5fdc.e433   999    Dynamic   gpon-onu_1/2/9:25         vport 3


== CHEKING ONT UPTIME AND ONT HISTORY LOGS ==

iSerius(config)#show gpon onu detail-info gpon-onu_1/2/9:25


ONU interface:         gpon-onu_1/2/9:25
  Name:                   iSerius_999
  Type:                     jte
  State:                    ready
  Admin state:          enable
  Phase state:           working
  Authentication mode: sn
  SN Bind:                 enable with SN check
  Serial number:       HWTC6315FF9E
  Password:
  Device ID:
  Description:         iSerius_TailQuarter
  Vport mode:         gemport
  DBA Mode:            Hybrid
  ONU Status:          enable
  OMCI BW Profile:   enable
  Line Profile:          N/A
  Service Profile:      N/A
  Alarm Profile:        N/A
  Performance Profile: N/A
  ONU Distance:        1m
  Online Duration:     9h 26m 14s
  FEC:                      none
  1PPS+ToD:             disable
------------------------------------------
       Authpass Time          OfflineTime             Cause
   1   2020-08-15 10:06:20    2020-08-15 18:00:51     DyingGasp
   2   2020-08-15 18:01:35    2020-08-16 07:14:22     DyingGasp
   3   2020-08-16 07:16:14    2020-08-24 11:07:51     DyingGasp
   4   2020-08-24 11:08:56    2020-08-28 00:52:38     LOSi
   5   2020-08-28 00:53:27    0000-00-00 00:00:00
   6   0000-00-00 00:00:00    0000-00-00 00:00:00
   7   0000-00-00 00:00:00    0000-00-00 00:00:00
   8   0000-00-00 00:00:00    0000-00-00 00:00:00
   9   0000-00-00 00:00:00    0000-00-00 00:00:00
  10   0000-00-00 00:00:00    0000-00-00 00:00:00

==  FINDING ONT BY SN NUMBER ==

iSerius(config)#show gpon onu by sn ZTEGC223344A

SearchResult
-----------------
gpon-onu_1/2/7:1
gpon-onu_1/2/9:25


== CHECKING ONT VERSION ==


iSerius(config)#show gpon remote-onu equip gpon-onu_1/2/3:1


== CHECKING OLT UPTIME ==

iSerius(config)#show system-group


== CHECKING OLT BOARD ==

GPON#show card

== CHECKING OLT PROCESSOR AND MEMORY ==

GPON#show processor

== CHECKING OLT CARD TEMPERATURE ==

GPON#show card-temperature


== CHECKING OLT PER SLOT ==

GPON#show card slotno 2

GPON#show card slotno 3

GPON#show card slotno 4



== CHECKING ONT IP ROUTING MODE ==

gpon# show gpon remote-onu ip-host  gpon-onu_1/2/1:3


== CHECKING ONT CONFIGURATION ==

GPON#show run int gpon-onu_1/4/1:2

== REBOOT ONT ==

gpon#config t
gpon#pon-onu-mng gpon-onu_1/2/1:3
gpon(gpon-onu-mng)#reboot


== RESET FACTORY ONT ==

gpon#config t
gpon#pon-onu-mng gpon-onu_1/2/1:3
gpon(gpon-onu-mng)#restore factory


### DISABLE/SHUTDOWN PORT ONT

gpon#config t
gpon#pon-onu-mng gpon-onu_1/2/1:3
gpon(gpon-onu-mng)#interface eth eth_0/2 state lock --> disable/shutdown port number 2


### ENABLE/SHUTDOWN PORT ONT

gpon#config t
gpon#pon-onu-mng gpon-onu_1/2/1:3
gpon(gpon-onu-mng)#interface eth eth_0/2 state unlock --> enable port number 2



###  RELEASE RENEW ONT AS DHCP CLIENT

GPON#config t
Enter configuration commands, one per line.  End with CTRL/Z.
GPON(config)#pon-onu
GPON(config)#pon-onu-mng gpon-onu_1/2/1:3
GPON(gpon-onu-mng)#ip-host 1 dhcp-enable false ping-response false traceroute-response false
GPON(gpon-onu-mng)#ip-host 1 dhcp-enable true ping-response true traceroute-response true



### CHECKING RX/TX LEVEL UPLINK PORT

GPON#sho int optical-module-info xgei_1/21/1


### RESET SLOT CARD

GPON#reset-card slotno 2



### SWAP

Use This for First Level Handling when you get Anomaly Process.
sometimes it can help you, but sometime isn’t

GPON#swap



### SHOW VLAN SUMMARY

GPON# show vlan summary
All created vlan num: 3
Details are following:
111, 222 , 333
GPON#
GPON#show vlan 111
vlanid          :111
name            :VLAN00111
description     :N/A
multicast-packet:flood-unknown
tpid:0x8100
port(untagged):
port(tagged):
gpon-onu_1/2/1:3:6
xgei_1/3/4
sg1



### CHECKING BANDWIDTH PROFLE

GPON#show gpon profile traffic


1. Cek Detail Config di Interface ke arah ONT
OLT-ZTE_C320#show run interface gpon-onu_1/2/5:4
Building configuration…
!
interface gpon-onu_1/2/5:4
  name Customer-1
  description Internet-Customer-1
  tcont 1 name acsata profile UP-50M
  gemport 1 name Internet unicast tcont 1 dir both
  gemport 1 traffic-limit upstream DOWN-50M downstream DOWN-50M
  switchport mode hybrid vport 1
  service-port 1 vport 1 user-vlan 1247 vlan 1247 svlan 1402
!
end

OLT-ZTE_C320#show run interface gpon-onu_1/2/5:5
Building configuration…
!
interface gpon-onu_1/2/5:5
  name Customer-2
  description Internet-Customer-2
  tcont 1 name acsata profile UP-60M
  tcont 1 gap mode2
  gemport 1 name Internet unicast tcont 1 dir both
  gemport 1 traffic-limit upstream DOWN-60M downstream DOWN-60M
  switchport mode hybrid vport 1
  service-port 1 vport 1 user-vlan 1245 vlan 1245 svlan 1402
!
end


2. Cek Status Interface ONT

OLT-ZTE_C320#show gpon onu state gpon-olt_1/2/5 4      
 

OLT_ZTE_C320#show gpon onu state gpon-olt_1/2/5 5

OLT-ZTE_C320#show pon power attenuation gpon-onu_1/2/5:4           

4. Cek Utilisasi Bandwith Link ONT Real Time

OLT-ZTE_C320#show interface gpon-onu_1/2/5:4

OLT-ZTE_C320#show interface gpon-onu_1/2/5:5

5. Cek ONT Uptime dan History:

OLT-ZTE_C320#show gpon onu detail-info gpon-onu_1/2/5:5

6. Cek Mac Address Perangkat yang terkoneksi ke ONT

OLT-ZTE_C320#show mac gpon onu gpon-onu_1/2/5:5

7. Cek ONT Version

OLT-ZTE_C320#show gpon remote-onu equip gpon-onu_1/2/5:5

8. Cek Status Port di ONT

OLT-ZTE_C320#show gpon remote-onu interface eth gpon-onu_1/2/5:5

9. Reboot/Restart ONT

OLT-ZTE_C320(config)#pon-onu-mng gpon-onu_1/2/5:5
OLT-ZTE_C320(gpon-onu-mng)#reboot

10. Shutdown Port 1 di ONT

OLT-ZTE_C320(config)#pon-onu-mng gpon-onu_1/2/5:5
OLT-ZTE_C320(gpon-onu-mng)#interface eth eth_0/1 state lock
11. Cek Konfigurasi PON ONU
OLT_ZTE_C320#show onu running config gpon-onu_1/2/11:8
pon-onu-mng gpon-onu_1/2/11:8
  service Internet-Customer1 gemport 1 vlan 671
  service OAM gemport 2 vlan 1450
  service Internet-Customer2 gemport 3 vlan 1490
  vlan port eth_0/1 mode tag vlan 671
  vlan port eth_0/3 mode tag vlan 1490

at August 24, 2020 
Email This
BlogThis!
Share to Twitter
Share to Facebook
Share to Pinterest
28 March 2019
bridge setting gpon f660 f609 di zte olt c320
    interface gpon-olt_1/2/13
    onu 1 type jte sn ZTEGxxxxxxx
    exit
   
   
iSerius(config)#interface gpon-onu_1/2/13:3
iSerius(config-if)#name iSerius_072
iSerius(config-if)#description bridge di tib36b
iSerius(config-if)#vport-mode gemport def-map-type 1:1
iSerius(config-if)#tcont 1 name BR profile 50M
iSerius(config-if)#tcont 1 gap mode2
iSerius(config-if)#gemport 1 name BR unicast tcont 1 dir both queue 1
iSerius(config-if)#gemport 1 traffic-limit upstream UP-20M downstream DOWN-20M
iSerius(config-if)#switchport mode hybrid vport 1
iSerius(config-if)#switchport vlan 177 tag vport 1
iSerius(config-if)#exit


iSerius(config)#pon-onu-mng gpon-onu_1/2/13:3
iSerius(gpon-onu-mng)#service BR gemport 1 vlan 177

##(ini bridge vlan wifi portnya..)

iSerius(gpon-onu-mng)#vlan port wifi_0/1 mode tag vlan 177
iSerius(gpon-onu-mng)#vlan port wifi_0/2 mode tag vlan 177
iSerius(gpon-onu-mng)#vlan port wifi_0/3 mode tag vlan 177
iSerius(gpon-onu-mng)#vlan port wifi_0/4 mode tag vlan 177

##(ini bridge vlan eth portnya..)

iSerius(gpon-onu-mng)#vlan port eth_0/1 mode tag vlan 177
iSerius(gpon-onu-mng)#vlan port eth_0/2 mode tag vlan 177
iSerius(gpon-onu-mng)#vlan port eth_0/3 mode tag vlan 177
iSerius(gpon-onu-mng)#vlan port eth_0/4 mode tag vlan 177

##(ini setting dhcp to wan di web confignya)

iSerius(gpon-onu-mng)#dhcp-ip ethuni eth_0/1 from-internet
iSerius(gpon-onu-mng)#dhcp-ip ethuni eth_0/2 from-internet
iSerius(gpon-onu-mng)#dhcp-ip ethuni eth_0/3 from-internet
iSerius(gpon-onu-mng)#dhcp-ip ethuni eth_0/4 from-internet
iSerius(gpon-onu-mng)#switchport-bind switch_0/1 iphost 1
iSerius(gpon-onu-mng)#pppoe 1 nat enable user bridge_tib36b password bridge
iSerius(gpon-onu-mng)#onu-vlan iphost 1 up-mode add up-prio 0 up-vid 177 down-mode transparent
iSerius(gpon-onu-mng)#security-mng 1 ingress-type wan mode permit state enable protocol web
## make ont reachable from wan side

iSerius(gpon-onu-mng)#exit
iSerius(gpon-onu-mng)#exit
iSerius(config)#exit
iSerius#wr


beres




fungsi dibawah untuk setting enable /disable wifi dan ganti nama SSID , tapi hanya bisa di F609 di F660 tidak berfungsi

ssid ctrl wifi_0/1 name iSerius_hiji hide enable max-users 20 user-isolation enable
ssid ctrl wifi_0/2 name iSerius_dua hide enable max-users 20 user-isolation enable
ssid ctrl wifi_0/3 name iSerius_tiga hide enable max-users 20 user-isolation enable
ssid ctrl wifi_0/4 name iSerius_fiberglass hide disable max-users 20 user-isolation disable

interface wifi wifi_0/2 state unlock
interface wifi wifi_0/3 state unlock
interface wifi wifi_0/4 state unlock