AP3602I

Как отлисчить IOS

ap3g2-k9w8-mx.153-3.JF10 vs ap3g2-k9w7-mx.153-3.JD3

Именвание platform-featureset-tar.version.tar

• ap3g2-k9w8-mx.153-3.JF10

platform- the access point hardware model or family supported by the image. Note: on an AireOS controller, the command show ap bundle shows the supported AP models and the corresponding platform names. On the 9800, use show ap image file summary. ap1g1 - 700 series (702w beginning with 15.2(4)JB5) ap1g2 - 1600 series

ap1g3 - 1530 series, AP803 embedded in IR829 router

ap1g4 - 1850/1830/1810 series (AP-COS)

ap1g5 - 1800/1815/1840/1540 series; AP1100AC embedded in C1000 series ISR (AP-COS) ap1g6 - C9117 (AP-COS) ap1g6a - C9124, C9130, C9136, IW9167, CW9164, CW9166 (AP-COS) ap1g6b - CW9162I ap1g7 - C9115/9120 (AP-COS) ap1g8 - C9105 (AP-COS) ap3g1 - 3500/1260 series ap3g2 - 3700/3600/2700/2600/1700 series (aIOS, and lightweight up through 8.4/15.3(3)JE branch)

ap3g3 - 2800/3800/4800/1560/IW6300/ESW6300 series (AP-COS) ap801 - AP embedded in 861W, CISCO88xW, CISCO891W, 1911W routers ap802 - AP embedded in 819, 812, 886VA-W/887VA-W, and C88x/C89x routers apw5100 - Rockwell Stratix 5100 WAPAK9, WAPCK9, WAPEK9, WAPZK9 c3700 - 1700/2700/3700 series APs (lightweight, 8.5/15.3(3)JF and above) c1570 - 1570 series outdoor APs c1550 - 1550 (128MB model) series outdoor APs c1520 - 1520 and 1550 (64MB model) series mesh APs c1410 - BR1410 c1310 - BR1310 c1250 - 1250 series APs c1240 - 1240 series APs c1200 - 1200 series (1200/1210/1220/1230) c1140 - 1140 and 1040 series APs c1130 - 1130 series APs c1100 - 1100 series APs (i.e. the AP1121) c520 - 521 AP c350 - 350 series APs featureset- the set of software features supported by the image - one of: k9w7 - autonomous (or "site survey") IOS (not available with AP-COS) k9w8 - full lightweight IOS/AP-COS (this is what is bundled in the WLC .aes image, and is factory installed on "mesh" APs) rcvk9w8 - lightweight recovery image - this is factory installed on lightweight APs, unless a "mesh" image is specified; it lacks radio firmware (not available with COS) boot - bootloader image (not IOS) - normally installed by manufacturing and not updated in the field version- the IOS version There is a 1:1 mapping between the lightweight OS software version (such as 12.4(23c)JA) and the CUWN version (such as 7.0.98.0) see the Wireless Solutions Software Compatibility Matrix on CCO Example: c1240-k9w7-tar.124-25d.JA1.tar

Platform: c1240: 1240 series AP Featureset: k9w7: autonomous IOS Version: 124-25d.JA1: 12.4(25d)JA1

As AP IOS is always distributed as a tar file, the AP cannot directly execute such a file (thus, if you were to copy c1240-k9w7-tar.124-25d.JA1.tar directly onto AP flash, and then try to boot it, this could not work.) The tar file contains, in addition to the IOS image proper, the radio firmware files, the HTML GUI files (if present), and various other files.

The AP IOS tar file must be unbundled into AP flash using the archive exec command (this is done in an automated fashion when a lightweight AP is upgraded after joining a WLC.)

Example: AP1260#archive download-sw /overwrite tftp://10.95.42.136/ap3g1-k9w7-tar.124-25d.JA1

After unbundling, the IOS image itself be in a file called flash:/platform-featureset-mx.version/platform-featureset-mx.version - for example, flash:/c1240-k9w7-mx.124-25d.JA1/c1240-k9w7-mx.124-25d.JA1. The AP is configured to boot this image if the bootloader BOOT environmental variable is set accordingly.

To see what IOS image the AP is configured to boot, examine the BOOT variable.

Example: AP3502i#more flash:/env_vars | include BOOT

BOOT=flash:/ap3g1-k9w8-mx.152-2.JA/ap3g1-k9w8-mx.152-2.JA

To change the BOOT variable, use the IOS config mode boot system command.

Example:

AP3502i(config)#boot system flash:/ap3g1-k9w8-mx.124-25e.JA2/ap3g1-k9w8-mx.124-25e.JA2

Как отконвертить точку для работы в stand-alone режиме без контроллера

• отключить питание
• зажать mode
• держать пока точка на консоль ненапишет что увидела нажатие
• enable
• debug capwap console cli
• debug capwap client no-reload
• capwap ap ip address 10.0.0.2 255.255.255.0
• capwap ap ip default-gateway 10.0.0.1
• archive download-sw /force /overwrite tftp://10.0.0.1/filename.tar
• Ждать - точка сама распакует все что нужно (если не хватило места - удалить что-то ненужное)
• После распаковки - сама перезагрузеится, адрес останется тот что был (в примере 10.0.0.2)

то же самое из rommon (Не могу сказать как мне удалось загнать точку в такой режим, но удалось)

Requirements:
1.TFTPd64 Server
2.Cisco IOS Software AP3G2-K9W7-M for (C3600 Series AP)
3.The Cisco AP and the Laptop with TFTP server must be in same network.

According to my network setup
Lightweight AP BVI1 IP address is 192.168.1.4
Laptop's IP address where TFTP server is installed 192.168.1.7 [Default Router IP]

First disconnect the ethernet cable from the AP then Press the Mode button and Put back the ethernet cable to the AP and hold the Mode button Untill flash light turns to umber and Once the Lightweight AP goes to online then apply the following commands to convert it to Autonomous version:

set IP_ADDR 192.168.1.4 [According to my network setup]
set NETMASK 255.255.255.0 [According to my network setup]
set DEFAULT_ROUTER 192.168.1.7 [According to my network setup]
tftp_init
ether_init
flash_init
tar -xtract tftp://192.168.1.7/ap3g2-k9w7-tar.153-3.JH.tar flash:
dir flash
set boot flash:/ap3g2-k9w7-mx.153-3.JH/ap3g2-k9w7-mx.153-3.JH
set
boot