Intel unsupported sfp

Ошибка ixgbe failed to load because an unsupported SFP+ module type was detected

• https://forums.servethehome.com/index.php?threads/patching-intel-x520-eeprom-to-unlock-all-sfp-transceivers.24634/

x520

• файл /etc/default/grub.d/60_custom.cfg

GRUB_CMDLINE_LINUX="$GRUB_CMDLINE_LINUX ixgbe.allow_unsupported_sfp=1"

Или если более чем одна карта - ixgbe.allow_unsupported_sfp=1,1,1,1

• Запустить update-grub

• Файл /etc/modprobe.d/ixgbe.conf

options ixgbe allow_unsupported_sfp=1,1,1,1

Тут нужно указать список если более чем одна карта (или порт?)

x520 Unlocker

В теории это нужно что бы установить карту там, где драйвер не имеет опции отключения проверки.
Последний бит должен быть установлен 1 (в примере уже установлен, в обоих случаях )

ethtool -e enp3s0f1  offset 0x58 length 1
Offset		Values
------		------
0x0058:		fd

ethtool -e enp7s0f0 offset 0x58 length 1
Offset		Values
------		------
0x0058:		ff

Все манипуляции проводить только с 1 битом, например если было значение fe
( Бинарное 11111110 ) то записать следует ff( Бинарное 11111111

 ethtool -E enp1s0 magic 0x10fb8086 offset 0x58 value 0xff​

Магическое значение можно посмотреть так:

lspci -nn | grep 82599
03:00.0 Ethernet controller [0200]: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection [8086:10fb] (rev 01)
03:00.1 Ethernet controller [0200]: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection [8086:10fb] (rev 01)

[8086:10fb] --> 0x 10fb 8086

Что бы не возиться руками все те же манипуляции можно сделать скриптом

cat intel_x520_patcher.py
#!/usr/bin/env python3
#
# Simple Intel x520 EEPROM patcher
# Modifies the EEPROM to unlock the card for non-intel branded SFP modules.
#
# Copyright 2020,2021,2022 Andreas Thienemann <andreas@bawue.net>
#
# Licensed under the GPLv3
#
# Based on research described at https://forums.servethehome.com/index.php?threads/patching-intel-x520-eeprom-to-unlock-all-sfp-transceivers.24634/
#
# Quick explanation of what's going on:
# Looking at the Intel driver at e.g. https://elixir.bootlin.com/linux/v5.8/source/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h#L2140 we can see
# that the bit 0x1 at Address 0x58 contains a configuration setting whether the card allows any SFP modules or if Intel specific ones are enforced
# by the driver.
#
# Addr Bitstring
# 0x58 xxxxxxx0 means Intel specific SFPs
# 0x58 xxxxxxx1 means any SFP is allowed.
#
# Using the parameter allow_unsupported_sfp for the kernel module we can tell the driver to accept any SFPs.
# But this tool will flip the right bit 1 to make that change permanent in the configuration bits in the EEPROM,
# thus making kernel module parameters unnecessary.
#

import subprocess
import sys

try:
    intf = sys.argv[1]
except IndexError:
    print("%s <interface>" % sys.argv[0])
    sys.exit(255)

try:
    with open("/sys/class/net/%s/device/vendor" % intf) as f:
        vdr_id = f.read().strip()

    with open("/sys/class/net/%s/device/device" % intf) as f:
        dev_id = f.read().strip()
except IOError:
    print("Can't read interface data.")
    sys.exit(2)

if vdr_id not in ('0x8086') or dev_id not in ('0x10fb', '0x154d'):
    print("Not a recognized Intel x520 card.")
    sys.exit(3)


output = subprocess.check_output(['ethtool', '-e', intf, 'offset', '0x58', 'length', '1'])
print(output)
v = output.strip().decode('utf-8').split('\n')
print(v)
val = output.strip().decode('utf-8').split('\n')[-1].split()[-1]
val_bin = int(val, 16)


print("EEPROM Value at 0x58 is 0x%s (%s)" % (val, bin(val_bin)))
if val_bin & 0b00000001 == 1:
    print("Card is already unlocked for all SFP modules. Nothing to do.")
    exit(1)
if val_bin & 0b00000001 == 0:
    print("Card is locked to Intel only SFP modules. Patching EEPROM...")
    new_val = val_bin | 0b00000001
    print("New EEPROM Value at 0x58 will be %s (%s)" % (hex(new_val), bin(new_val)))

magic = "%s%s" % (dev_id, vdr_id[2:])
cmd = ['ethtool', '-E', intf, 'magic', magic, 'offset', '0x58', 'value', hex(new_val), 'length', 1]
print("Running %s" % " ".join(cmd))
#subprocess.call(cmd)
print("Reboot the machine for changes to take effect...")

xl710

• https://github.com/bibigon812/xl710-unlocker

# ./xl710_unlock -n enp4s0f0
EMP SR offset: 0x67a8
PHY offset: 0x68f6
PHY data struct size: 0x000c
MISC: 0x6b0c <- locked
MISC: 0x6b0c <- locked
MISC: 0x6b0c <- locked
MISC: 0x6b0c <- locked
Ready to fix it? [y/N]: y

TARGETS = xl710_unlock

all: $(TARGETS)

clean:
	rm -f $(TARGETS)

%:	%.c
	gcc -Wall -O2 $< -o $@