HP Proliant Raid

DL180 G6

lspci | grep -i raid
09:00.0 RAID bus controller: Hewlett-Packard Company Smart Array G6 controllers (rev 01)

lspci -vv  -s 09:00.0
09:00.0 RAID bus controller: Hewlett-Packard Company Smart Array G6 controllers (rev 01)
	Subsystem: Hewlett-Packard Company Smart Array P410
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 256 bytes
	Interrupt: pin A routed to IRQ 37
	Region 0: Memory at fbc00000 (64-bit, non-prefetchable) [size=2M]
	Region 2: Memory at fbbff000 (64-bit, non-prefetchable) [size=4K]
	Region 4: I/O ports at d800 [size=256]
	Expansion ROM at fbb00000 [disabled] [size=512K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [70] Express (v2) Endpoint, MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
		DevCtl:	CorrErr- NonFatalErr+ FatalErr+ UnsupReq-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 256 bytes, MaxReadReq 4096 bytes
		DevSta:	CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 5GT/s, Width x8, ASPM not supported
			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
		LnkCtl:	ASPM Disabled; RCB 64 bytes, Disabled- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s (downgraded), Width x8 (ok)
			TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis+ NROPrPrP- LTR-
			 10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
			 EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
			 FRS- TPHComp- ExtTPHComp-
			 AtomicOpsCap: 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
			 AtomicOpsCtl: ReqEn-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
			 EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
			 Retimer- 2Retimers- CrosslinkRes: unsupported
	Capabilities: [ac] MSI-X: Enable+ Count=16 Masked-
		Vector table: BAR=0 offset=001c2000
		PBA: BAR=0 offset=001c4000
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
		AERCap:	First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
			MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
		HeaderLog: 00000000 00000000 00000000 00000000
	Kernel driver in use: hpsa
	Kernel modules: hpsa

Утилиты

• https://downloads.linux.hpe.com/SDR/repo/mcp/ubuntu/pool/non-free/

(я доставал файлы так как в пакете сломаны зависимости)

Сокращения, которые можно использовать в командах

• chassisname = ch
• controller = ctrl
• logicaldrive = ld
• physicaldrive = pd
• drivewritecache = dwc

Просмотр конфигурации

hpacucli ctrl all show config

Smart Array P410 in Slot 1                (sn: PACCR9SYRIHU  )
   unassigned
      physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK)
   SEP (Vendor ID PMCSIERA, Model  SRC 8x6G) 250 (WWID: 5001438006116C2F)

Тут в примере - один диск который включен но никак не настроен

Более детально:

hpacucli ctrl all show config detail

Smart Array P410 in Slot 1
   Bus Interface: PCI
   Slot: 1
   Serial Number: PACCR9SYRIHU
   Cache Serial Number: PAAVP9SYYM4C
   RAID 6 (ADG) Status: Disabled
   Controller Status: OK
   Hardware Revision: C
   Firmware Version: 6.64
   Wait for Cache Room: Disabled
   Surface Analysis Inconsistency Notification: Disabled
   Post Prompt Timeout: 0 secs
   Cache Board Present: True
   Cache Status: Not Configured
   Drive Write Cache: Disabled
   Total Cache Size: 512 MB
   Total Cache Memory Available: 400 MB
   No-Battery Write Cache: Disabled
   Battery/Capacitor Count: 0
   SATA NCQ Supported: True



   unassigned

      physicaldrive 2I:1:3
         Port: 2I
         Box: 1
         Bay: 3
         Status: OK
         Drive Type: Unassigned Drive
         Interface Type: SAS
         Size: 300 GB
         Rotational Speed: 10000
         Firmware Revision: HPD7
         Serial Number: 6XP5CLK80000B335CPL7
         Model: HP      EG0300FBLSE
         PHY Count: 2
         PHY Transfer Rate: 6.0Gbps, Unknown


   SEP (Vendor ID PMCSIERA, Model  SRC 8x6G) 250
      Device Number: 250
      Firmware Version: RevC
      WWID: 5001438006116C2F
      Vendor ID: PMCSIERA
      Model:  SRC 8x6G

Статус контроллера

hpacucli ctrl all show status

Smart Array P410 in Slot 1
   Controller Status: OK
   Cache Status: Not Configured

Управление кэшированием

hpacucli ctrl slot=1 modify dwc=disable

Error: This operation is not supported with the current configuration. Use the
       "show" command on devices to show additional details about the
       configuration.
Reason: Controller not configured

hpacucli ctrl slot=1 modify dwc=enable

Warning: Without the proper safety precautions, use of write cache on physical
         drives could cause data loss in the event of power failure.  To ensure
         data is properly protected, use redundant power supplies and
         Uninterruptible Power Supplies. Also, if you have multiple storage
         enclosures, all data should be mirrored across them. Use of this
         feature is not recommended unless these precautions are followed.
         Continue? (y/n)

У меня не включился, думаю из-за

   Battery/Capacitor Count: 0

Пересканировать устройства

Пересканировать устройства, добавленные с момента последнего сканирования

hpacucli rescandetects newly added devices since the last rescan

В моем случае ни к чему не привело - диск нашелся сам по себе

Просмотр информации по отдельному диску

hpacucli ctrl slot=1 pd 2I:1:3 show detail

Smart Array P410 in Slot 1

   unassigned

      physicaldrive 2I:1:3
         Port: 2I
         Box: 1
         Bay: 3
         Status: OK
         Drive Type: Unassigned Drive
         Interface Type: SAS
         Size: 300 GB
         Rotational Speed: 10000
         Firmware Revision: HPD7
         Serial Number: 6XP5CLK80000B335CPL7
         Model: HP      EG0300FBLSE
         PHY Count: 2
         PHY Transfer Rate: 6.0Gbps, Unknown

Во многих примерах приводят pd 2:3 (2-х значный адрес) вместо pd 2I:1:3 (3-х значный), возможно связано с версией контроллера или утилит.
Сам адрес диска, если он не известен можно посмотреть в hpacucli ctrl all show config detail

    physicaldrive 2I:1:3
         Port: 2I
         Box: 1
         Bay: 3

Статус дисков

Все диски

hpacucli ctrl slot=1 pd all show status
   physicaldrive 2I:1:3 (port 2I:box 1:bay 3, 300 GB): OK

Или отдельный диск (а он тут всего один)

hpacucli ctrl slot=1 pd 2I:1:3 show status
   physicaldrive 2I:1:3 (port 2I:box 1:bay 3, 300 GB): OK

Очистка

hpacucli ctrl slot=1 pd 2I:1:3 modify erase

Управление диодами на дисках

hpacucli ctrl slot=1 pd 2I:1:3 modify led=on

hpacucli ctrl slot=1 pd 2I:1:3 modify led=off

Показать информацию (детально)

hpacucli ctrl slot=1 ld all show detail

Error: The specified device does not have any logical drives.

Логических дисков пока нет