3ware 9650SE: различия между версиями

Материал из noname.com.ua
Перейти к навигацииПерейти к поиску
 
(не показано 7 промежуточных версий 2 участников)
Строка 1: Строка 1:
  +
[[Категория:Hardware]]
  +
[[Категория:Raid]]
  +
[[Категория: Raid]]
  +
[[Категория: 3ware]]
  +
[[Категория: Linux]]
 
=3ware 9650SE=
 
=3ware 9650SE=
  +
Этот текст - напоминание самому себе, потому что так редко пользуюсь tw_cli что приходиться читать ман каждый раз.
  +
  +
  +
 
В какой то момент времени понадобилось подключить 4 диска (потестировать) а свободные были только порты в таком контроллере:
 
В какой то момент времени понадобилось подключить 4 диска (потестировать) а свободные были только порты в таком контроллере:
 
<PRE>
 
<PRE>
Строка 22: Строка 31:
 
dmesg
 
dmesg
 
[874800.760969] 3w-9xxx: scsi6: AEN: INFO (0x04:0x001A): Drive inserted:port=2.
 
[874800.760969] 3w-9xxx: scsi6: AEN: INFO (0x04:0x001A): Drive inserted:port=2.
  +
</PRE>
  +
  +
<PRE>
  +
/c6 show all
  +
..
  +
Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy
  +
------------------------------------------------------------------------------
  +
u0 SINGLE OK - - - 465.651 ON OFF
  +
  +
Port Status Unit Size Blocks Serial
  +
---------------------------------------------------------------
  +
p0 OK u0 465.76 GB 976771055 9QM14TZV
  +
p1 NOT-PRESENT - - - -
  +
p2 OK - 298.09 GB 625142448 3QF0ZBRW
  +
p3 NOT-PRESENT - - - -
  +
</PRE>
  +
  +
<PRE>
  +
//sirmax> /c6 add type=single disk=2
  +
</PRE>
  +
  +
<PRE>
  +
//sirmax> /c show all
  +
Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy
  +
------------------------------------------------------------------------------
  +
u0 SINGLE OK - - - 465.651 ON OFF
  +
u1 SINGLE OK - - - 298.013 ON OFF
  +
  +
Port Status Unit Size Blocks Serial
  +
---------------------------------------------------------------
  +
p0 OK u0 465.76 GB 976771055 9QM14TZV
  +
p1 NOT-PRESENT - - - -
  +
p2 OK u1 298.09 GB 625142448 3QF0ZBRW
  +
p3 NOT-PRESENT - - - -
  +
</PRE>
  +
<PRE>
  +
[876313.950488] scsi 6:0:1:0: Direct-Access AMCC 9650SE-4LP DISK 3.08 PQ: 0 ANSI: 5
  +
[876313.950738] sd 6:0:1:0: Attached scsi generic sg7 type 0
  +
[876313.951734] sd 6:0:1:0: [sdg] 624977920 512-byte logical blocks: (319 GB/298 GiB)
  +
[876313.952292] sd 6:0:1:0: [sdg] Write Protect is off
  +
[876313.952296] sd 6:0:1:0: [sdg] Mode Sense: 23 00 00 00
  +
[876313.952853] sd 6:0:1:0: [sdg] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
  +
[876313.953890] sdg: unknown partition table
  +
[876314.091818] sd 6:0:1:0: [sdg] Attached SCSI disk
  +
</PRE>
  +
  +
  +
  +
  +
  +
<PRE>
  +
sirmax ~ # smartctl -i -d 3ware,2 /dev/twa0
  +
smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
  +
Home page is http://smartmontools.sourceforge.net/
  +
  +
=== START OF INFORMATION SECTION ===
  +
Model Family: Seagate Barracuda 7200.10 family
  +
Device Model: ST3320620AS
  +
Serial Number: 3QF0ZBRW
  +
Firmware Version: 3.AAE
  +
User Capacity: 320,072,933,376 bytes
  +
Device is: In smartctl database [for details use: -P show]
  +
ATA Version is: 7
  +
ATA Standard is: Exact ATA specification draft version not indicated
  +
Local Time is: Sat Apr 3 14:20:31 2010 EEST
  +
SMART support is: Available - device has SMART capability.
  +
SMART support is: Enabled
  +
</PRE>
  +
  +
<PRE>
  +
sirmax ~ # smartctl -A -d 3ware,0 /dev/twa0
  +
smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
  +
Home page is http://smartmontools.sourceforge.net/
  +
  +
=== START OF READ SMART DATA SECTION ===
  +
SMART Attributes Data Structure revision number: 10
  +
Vendor Specific SMART Attributes with Thresholds:
  +
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
  +
1 Raw_Read_Error_Rate 0x000f 093 090 006 Pre-fail Always - 165443963
  +
3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0
  +
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 166
  +
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 2047
  +
7 Seek_Error_Rate 0x000f 077 060 030 Pre-fail Always - 17403638360
  +
9 Power_On_Hours 0x0032 083 083 000 Old_age Always - 15250
  +
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
  +
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 129
  +
184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0
  +
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
  +
188 Unknown_Attribute 0x0032 100 088 000 Old_age Always - 51541901626
  +
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
  +
190 Airflow_Temperature_Cel 0x0022 061 053 045 Old_age Always - 39 (Lifetime Min/Max 36/47)
  +
194 Temperature_Celsius 0x0022 039 047 000 Old_age Always - 39 (0 5 0 0)
  +
195 Hardware_ECC_Recovered 0x001a 040 028 000 Old_age Always - 165443963
  +
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
  +
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
  +
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1
  +
</PRE>
  +
  +
  +
  +
  +
  +
  +
  +
  +
  +
  +
<PRE>
  +
smartctl -a -d 3ware,2 /dev/twa0
  +
smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
  +
Home page is http://smartmontools.sourceforge.net/
  +
  +
=== START OF INFORMATION SECTION ===
  +
Model Family: Seagate Barracuda 7200.10 family
  +
Device Model: ST3320620AS
  +
Serial Number: 3QF0ZBRW
  +
Firmware Version: 3.AAE
  +
User Capacity: 320,072,933,376 bytes
  +
Device is: In smartctl database [for details use: -P show]
  +
ATA Version is: 7
  +
ATA Standard is: Exact ATA specification draft version not indicated
  +
Local Time is: Sat Apr 3 15:08:41 2010 EEST
  +
SMART support is: Available - device has SMART capability.
  +
SMART support is: Enabled
  +
  +
=== START OF READ SMART DATA SECTION ===
  +
SMART overall-health self-assessment test result: PASSED
  +
See vendor-specific Attribute list for marginal Attributes.
  +
  +
General SMART Values:
  +
Offline data collection status: (0x82) Offline data collection activity
  +
was completed without error.
  +
Auto Offline Data Collection: Enabled.
  +
Self-test execution status: ( 246) Self-test routine in progress...
  +
60% of test remaining.
  +
Total time to complete Offline
  +
data collection: ( 430) seconds.
  +
Offline data collection
  +
capabilities: (0x5b) SMART execute Offline immediate.
  +
Auto Offline data collection on/off support.
  +
Suspend Offline collection upon new
  +
command.
  +
Offline surface scan supported.
  +
Self-test supported.
  +
No Conveyance Self-test supported.
  +
Selective Self-test supported.
  +
SMART capabilities: (0x0003) Saves SMART data before entering
  +
power-saving mode.
  +
Supports SMART auto save timer.
  +
Error logging capability: (0x01) Error logging supported.
  +
General Purpose Logging supported.
  +
Short self-test routine
  +
recommended polling time: ( 1) minutes.
  +
Extended self-test routine
  +
recommended polling time: ( 115) minutes.
  +
  +
SMART Attributes Data Structure revision number: 10
  +
Vendor Specific SMART Attributes with Thresholds:
  +
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
  +
1 Raw_Read_Error_Rate 0x000f 119 091 006 Pre-fail Always - 229155998
  +
3 Spin_Up_Time 0x0003 096 095 000 Pre-fail Always - 0
  +
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 49
  +
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
  +
7 Seek_Error_Rate 0x000f 089 060 030 Pre-fail Always - 849154078
  +
9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 14424
  +
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
  +
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 75
  +
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
  +
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
  +
190 Airflow_Temperature_Cel 0x0022 051 035 045 Old_age Always In_the_past 49 (Lifetime Min/Max 26/49)
  +
194 Temperature_Celsius 0x0022 049 065 000 Old_age Always - 49 (0 18 0 0)
  +
195 Hardware_ECC_Recovered 0x001a 061 054 000 Old_age Always - 203295256
  +
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
  +
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
  +
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
  +
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
  +
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
  +
  +
SMART Error Log Version: 1
  +
No Errors Logged
  +
  +
SMART Self-test log structure revision number 1
  +
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
  +
# 1 Extended offline Self-test routine in progress 60% 14424 -
  +
  +
SMART Selective self-test log data structure revision number 1
  +
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
  +
1 0 0 Not_testing
  +
2 0 0 Not_testing
  +
3 0 0 Not_testing
  +
4 0 0 Not_testing
  +
5 0 0 Not_testing
  +
Selective self-test flags (0x0):
  +
After scanning selected spans, do NOT read-scan remainder of disk.
  +
If Selective self-test is pending on power-up, resume after 0 minute delay.
 
</PRE>
 
</PRE>

Текущая версия на 12:00, 4 сентября 2023

3ware 9650SE

Этот текст - напоминание самому себе, потому что так редко пользуюсь tw_cli что приходиться читать ман каждый раз.


В какой то момент времени понадобилось подключить 4 диска (потестировать) а свободные были только порты в таком контроллере:

02:00.0 RAID bus controller: 3ware Inc 9650SE SATA-II RAID PCIe (rev 01)
        Subsystem: 3ware Inc 9650SE SATA-II RAID PCIe
        Flags: bus master, fast devsel, latency 0, IRQ 16
        Memory at e2000000 (64-bit, prefetchable) [size=32M]
        Memory at e9000000 (64-bit, non-prefetchable) [size=4K]
        I/O ports at 9000 [size=256]
        [virtual] Expansion ROM at e8000000 [disabled] [size=128K]
        Capabilities: [40] Power Management version 2
        Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+
        Capabilities: [70] Express Legacy Endpoint, MSI 00
        Capabilities: [100] Advanced Error Reporting
        Kernel driver in use: 3w-9xxx
        Kernel modules: 3w-9xxx

После включения диска (сначала сигнальный шлейф, потом питание)

dmesg
[874800.760969] 3w-9xxx: scsi6: AEN: INFO (0x04:0x001A): Drive inserted:port=2.
/c6  show all
..
Unit  UnitType  Status         %RCmpl  %V/I/M  Stripe  Size(GB)  Cache  AVrfy
------------------------------------------------------------------------------
u0    SINGLE    OK             -       -       -       465.651   ON     OFF

Port   Status           Unit   Size        Blocks        Serial
---------------------------------------------------------------
p0     OK               u0     465.76 GB   976771055     9QM14TZV
p1     NOT-PRESENT      -      -           -             -
p2     OK               -      298.09 GB   625142448     3QF0ZBRW
p3     NOT-PRESENT      -      -           -             -
//sirmax>  /c6 add type=single disk=2
//sirmax>  /c show all
Unit  UnitType  Status         %RCmpl  %V/I/M  Stripe  Size(GB)  Cache  AVrfy
------------------------------------------------------------------------------
u0    SINGLE    OK             -       -       -       465.651   ON     OFF
u1    SINGLE    OK             -       -       -       298.013   ON     OFF

Port   Status           Unit   Size        Blocks        Serial
---------------------------------------------------------------
p0     OK               u0     465.76 GB   976771055     9QM14TZV
p1     NOT-PRESENT      -      -           -             -
p2     OK               u1     298.09 GB   625142448     3QF0ZBRW
p3     NOT-PRESENT      -      -           -             -
[876313.950488] scsi 6:0:1:0: Direct-Access     AMCC     9650SE-4LP DISK  3.08 PQ: 0 ANSI: 5
[876313.950738] sd 6:0:1:0: Attached scsi generic sg7 type 0
[876313.951734] sd 6:0:1:0: [sdg] 624977920 512-byte logical blocks: (319 GB/298 GiB)
[876313.952292] sd 6:0:1:0: [sdg] Write Protect is off
[876313.952296] sd 6:0:1:0: [sdg] Mode Sense: 23 00 00 00
[876313.952853] sd 6:0:1:0: [sdg] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
[876313.953890]  sdg: unknown partition table
[876314.091818] sd 6:0:1:0: [sdg] Attached SCSI disk



sirmax ~ # smartctl -i -d 3ware,2 /dev/twa0
smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.10 family
Device Model:     ST3320620AS
Serial Number:    3QF0ZBRW
Firmware Version: 3.AAE
User Capacity:    320,072,933,376 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Sat Apr  3 14:20:31 2010 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
sirmax ~ # smartctl -A -d 3ware,0 /dev/twa0
smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF READ SMART DATA SECTION ===
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   093   090   006    Pre-fail  Always       -       165443963
  3 Spin_Up_Time            0x0003   094   093   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       166
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       2047
  7 Seek_Error_Rate         0x000f   077   060   030    Pre-fail  Always       -       17403638360
  9 Power_On_Hours          0x0032   083   083   000    Old_age   Always       -       15250
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       129
184 Unknown_Attribute       0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Unknown_Attribute       0x0032   100   088   000    Old_age   Always       -       51541901626
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   061   053   045    Old_age   Always       -       39 (Lifetime Min/Max 36/47)
194 Temperature_Celsius     0x0022   039   047   000    Old_age   Always       -       39 (0 5 0 0)
195 Hardware_ECC_Recovered  0x001a   040   028   000    Old_age   Always       -       165443963
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       1






smartctl -a -d 3ware,2 /dev/twa0 
smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/                          

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.10 family
Device Model:     ST3320620AS                     
Serial Number:    3QF0ZBRW                        
Firmware Version: 3.AAE                           
User Capacity:    320,072,933,376 bytes           
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7                                              
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Sat Apr  3 15:08:41 2010 EEST                      
SMART support is: Available - device has SMART capability.           
SMART support is: Enabled                                            

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.    
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      ( 246) Self-test routine in progress...      
                                        60% of test remaining.
Total time to complete Offline
data collection:                 ( 430) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 115) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   119   091   006    Pre-fail  Always       -       229155998
  3 Spin_Up_Time            0x0003   096   095   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       49
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   089   060   030    Pre-fail  Always       -       849154078
  9 Power_On_Hours          0x0032   084   084   000    Old_age   Always       -       14424
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       75
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   051   035   045    Old_age   Always   In_the_past 49 (Lifetime Min/Max 26/49)
194 Temperature_Celsius     0x0022   049   065   000    Old_age   Always       -       49 (0 18 0 0)
195 Hardware_ECC_Recovered  0x001a   061   054   000    Old_age   Always       -       203295256
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 TA_Increase_Count       0x0032   100   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Self-test routine in progress 60%     14424         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.