Accton Edge Core ES 3526XA
Материал из noname.com.ua
Accton Edge-Core ES-3526XA
Цель статьи - описатьпроцедуру тестирования коммутатора Accton Edge-Core ES-3526XA. Планируется как замена Dlink DES-3526.
Загрузка
Наблюдаю загрузку (9600 8N1) с консоли. По первому впечатлению - не похож ни на один другой коммутатор.
Image Loader 1.0.0.2 Loading Diagnostic Image File : ES3526XA-V2_DIAG_1005.bix Diagnostic 1.0.0.5 --- Performing Power-On Self Tests (POST) --- DUMMY Test 1 ................. PASS UART Loopback Test ........... PASS DRAM Test .................... PASS I2C Bus Initialization ....... PASS Done All Pass. ------------------ DONE --------------------- Loading Runtime Image File : ES3526XA_ES3510_V11022.bix Runtime 1.1.0.22 root init done [get stackingMac done ret_val] = 1 Assigned Unit ID:[1] stacking DB: unit = 0, module type = 0 Set Transition mode ... Finish Set Transition mode ... Enter Transition mode ... Finish Transition mode ... Enter Master mode ... Load certificate files : Starting Load certificate files : Finished Finish Master mode ... Performing startup provision ... ............................................................................................................................................................................................................. Notify provision complete CLI provision has been completed Provision Complete ... Finish Provision Complete ... [get stackingMac done ret_val] = 1 *************************************************************** WARNING - MONITORED ACTIONS AND ACCESSES Station's information: Floor / Row / Rack / Sub-Rack / / / DC power supply: Power Source A: Floor / Row / Rack / Electrical circuit / / / Number of LP: Position MUX: IP LAN: Note: ********************************** User Access Verification Username:
Настройка
Не смотря на то что CLI вцелом cisco-like, это пожалуй самый неудобный в нстройке коммутатор из тех с которыми мне приходилось иметь дело.
DHCP Relay
Настройка коммутатора
Настройка достаточно простоа и вцелом аналогична другим коммутаторам (AT-8000S, Lucent LS-62..., DES- ...)
ip dhcp relay information option ip dhcp relay information option remote-id ip-address ip dhcp relay information policy replace IP DHCP relay server 172.16.251.1
Однако, отмечу что в пакете в качестве Remote-ID содержиться не ip а какой-то мусор. На данный момент у меня нет ответа от поставщика как расшифровать remote-id.
Настойка DHCPd
Вот пример пакета (только option 82)
Bootstrap Protocol
Message type: Boot Reply (2)
Hardware type: Ethernet
Hardware address length: 6
Hops: 1
Transaction ID: 0xa5ee3a70
Seconds elapsed: 0
Bootp flags: 0x8000 (Broadcast)
1... .... .... .... = Broadcast flag: Broadcast
.000 0000 0000 0000 = Reserved flags: 0x0000
Client IP address: 0.0.0.0 (0.0.0.0)
Your (client) IP address: 192.168.199.2 (192.168.199.2)
Next server IP address: 0.0.0.0 (0.0.0.0)
Relay agent IP address: 172.16.251.2 (172.16.251.2)
Client MAC address: 00:1c:23:95:8d:8b (00:1c:23:95:8d:8b)
Server host name not given
Boot file name not given
Magic cookie: (OK)
Option: (t=53,l=1) DHCP Message Type = DHCP Offer
Option: (53) DHCP Message Type
Length: 1
Value: 02
Option: (t=54,l=4) Server Identifier = 172.16.251.1
Option: (54) Server Identifier
Length: 4
Value: AC10FB01
Option: (t=51,l=4) IP Address Lease Time = 8 hours, 36 minutes, 40 seconds
Option: (51) IP Address Lease Time
Length: 4
Value: 00007918
Option: (t=1,l=4) Subnet Mask = 255.255.255.0
Option: (1) Subnet Mask
Length: 4
Value: FFFFFF00
Option: (t=3,l=4) Router = 192.168.199.254
Option: (3) Router
Length: 4
Value: C0A8C7FE
Option: (t=6,l=8) Domain Name Server
Option: (6) Domain Name Server
Length: 8
Value: C1213021C12130A0
IP Address: 193.33.48.33
IP Address: 193.33.48.160
Option: (t=82,l=16) Agent Information Option
Option: (82) Agent Information Option
Length: 16
Value: 01060004006501010206010400000000
Agent Circuit ID: 000400650101
Agent Remote ID: 010400000000
End Option
Padding
DHCP Snooping
При настройке DHCP Snopping мне удалось вызвать зависание коммутатора.
Пробую настроить согласно инструкции Монблана
<PRE> ip dhcp snooping ip dhcp snooping vlan 102 ip dhcp snooping information option ip dhcp snooping information policy replace
Console#sh ip dhcp snooping Global DHCP Snooping status: disable DHCP Snooping Information Option Status: disable DHCPSNP_MGR_GetInformationRidMode:3650 DHCPSNP_MGR_GetInformationRidMode:3657 DHCPSNP_MGR_GetInformationRidMode:3664 DHCPSNP_MGR_GetInformationRidMode:3666 DHCPSNP_MGR_GetInformationRidMode:3674 DHCPSNP_MGR_GetInformationRidMode:3677 CLI_API_Show_Ip_Dhcpsnp:450,rid mode = 1 DHCP Snooping Information Option Remote ID: mac address DHCP Snooping Information Policy: replace DHCP Snooping is configured on the following VLANs: 101, Verify Source Mac-Address: enable Interface Trusted ---------- ---------- Eth 1/1 No Eth 1/1 No Eth 1/1 No Eth 1/1 No Eth 1/1 No Eth 1/1 No Eth 1/1 No Eth 1/1 No Eth 1/1 No Eth 1/1 No Eth 1/1 No Eth 1/1 No Eth 1/1 No ...
