HP Proliant Raid: различия между версиями
Материал из noname.com.ua
Перейти к навигацииПерейти к поискуSirmax (обсуждение | вклад) |
Sirmax (обсуждение | вклад) (→P410) Метка: отменено |
||
| Строка 161: | Строка 161: | ||
Модуль ядра: <code>hpsa</code> |
Модуль ядра: <code>hpsa</code> |
||
|} |
|} |
||
| − | |||
| − | =<code>P410</code>= |
||
| − | <PRE> |
||
| − | lspci | grep -i raid |
||
| − | 09:00.0 RAID bus controller: Hewlett-Packard Company Smart Array G6 controllers (rev 01) |
||
| − | </PRE> |
||
| − | |||
| − | {{#spoiler:show=lspci -vv -s 09:00.0| |
||
| − | |||
| − | <PRE> |
||
| − | lspci -vv -s 09:00.0 |
||
| − | 09:00.0 RAID bus controller: Hewlett-Packard Company Smart Array G6 controllers (rev 01) |
||
| − | Subsystem: Hewlett-Packard Company Smart Array P410 |
||
| − | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+ |
||
| − | Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- |
||
| − | Latency: 0, Cache Line Size: 256 bytes |
||
| − | Interrupt: pin A routed to IRQ 37 |
||
| − | Region 0: Memory at fbc00000 (64-bit, non-prefetchable) [size=2M] |
||
| − | Region 2: Memory at fbbff000 (64-bit, non-prefetchable) [size=4K] |
||
| − | Region 4: I/O ports at d800 [size=256] |
||
| − | Expansion ROM at fbb00000 [disabled] [size=512K] |
||
| − | Capabilities: [40] Power Management version 3 |
||
| − | Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot-,D3cold-) |
||
| − | Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- |
||
| − | Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ |
||
| − | Address: 0000000000000000 Data: 0000 |
||
| − | Capabilities: [70] Express (v2) Endpoint, MSI 00 |
||
| − | DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us |
||
| − | ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W |
||
| − | DevCtl: CorrErr- NonFatalErr+ FatalErr+ UnsupReq- |
||
| − | RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ |
||
| − | MaxPayload 256 bytes, MaxReadReq 4096 bytes |
||
| − | DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr- TransPend- |
||
| − | LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM not supported |
||
| − | ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp- |
||
| − | LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk- |
||
| − | ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- |
||
| − | LnkSta: Speed 2.5GT/s (downgraded), Width x8 (ok) |
||
| − | TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- |
||
| − | DevCap2: Completion Timeout: Not Supported, TimeoutDis+ NROPrPrP- LTR- |
||
| − | 10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix- |
||
| − | EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- |
||
| − | FRS- TPHComp- ExtTPHComp- |
||
| − | AtomicOpsCap: 32bit- 64bit- 128bitCAS- |
||
| − | DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, |
||
| − | AtomicOpsCtl: ReqEn- |
||
| − | LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- |
||
| − | Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- |
||
| − | Compliance De-emphasis: -6dB |
||
| − | LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1- |
||
| − | EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- |
||
| − | Retimer- 2Retimers- CrosslinkRes: unsupported |
||
| − | Capabilities: [ac] MSI-X: Enable+ Count=16 Masked- |
||
| − | Vector table: BAR=0 offset=001c2000 |
||
| − | PBA: BAR=0 offset=001c4000 |
||
| − | Capabilities: [100 v1] Advanced Error Reporting |
||
| − | UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- |
||
| − | UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- |
||
| − | UESvrt: DLP+ SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- |
||
| − | CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ |
||
| − | CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ |
||
| − | AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- |
||
| − | MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- |
||
| − | HeaderLog: 00000000 00000000 00000000 00000000 |
||
| − | Kernel driver in use: hpsa |
||
| − | Kernel modules: hpsa |
||
| − | </PRE> |
||
| − | }} |
||
| − | |||
| − | ==Утилиты== |
||
| − | * https://downloads.linux.hpe.com/SDR/repo/mcp/ubuntu/pool/non-free/ |
||
| − | (я доставал файлы так как в пакете сломаны зависимости) |
||
| − | <PRE> |
||
| − | wget https://downloads.linux.hpe.com/SDR/repo/mcp/ubuntu/pool/non-free/hpacucli_9.40.1-1._amd64.deb |
||
| − | </PRE> |
||
| − | |||
| − | [[File:Hpacucli 9.40.1-1. amd64.deb]] |
||
| − | |||
| − | * Еще одно место где брать утилиты - http://hwraid.le-vert.net/wiki |
||
| − | |||
| − | {| class="wikitable" |
||
| − | |+ Утилиты |
||
| − | |- |
||
| − | ! |
||
| − | Текст заголовка |
||
| − | ! |
||
| − | Текст заголовка |
||
| − | |- |
||
| − | | |
||
| − | Текст ячейки |
||
| − | || |
||
| − | Текст ячейки |
||
| − | |- |
||
| − | | Текст ячейки || Текст ячейки |
||
| − | |- |
||
| − | | Текст ячейки || Текст ячейки |
||
| − | |} |
||
| − | |||
| − | ==Сокращения, которые можно использовать в командах== |
||
| − | |||
| − | * <code>chassisname</code> = <code>ch</code> |
||
| − | * <code>controller</code> = <code>ctrl</code> |
||
| − | * <code>logicaldrive</code> = <code>ld</code> |
||
| − | * <code>physicaldrive</code> = <code>pd</code> |
||
| − | * <code>drivewritecache</code> = <code>dwc</code> |
||
| − | |||
| − | ==Просмотр конфигурации== |
||
| − | <PRE> |
||
| − | hpacucli ctrl all show config |
||
| − | </PRE> |
||
| − | <PRE> |
||
| − | Smart Array P410 in Slot 1 (sn: PACCR9SYRIHU ) |
||
| − | unassigned |
||
| − | physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) |
||
| − | SEP (Vendor ID PMCSIERA, Model SRC 8x6G) 250 (WWID: 5001438006116C2F) |
||
| − | </PRE> |
||
| − | Тут в примере - один диск который включен но никак не настроен |
||
| − | <BR> |
||
| − | Более детально: {{#spoiler:show=hpacucli ctrl all show config detail| |
||
| − | |||
| − | <PRE> |
||
| − | hpacucli ctrl all show config detail |
||
| − | |||
| − | Smart Array P410 in Slot 1 |
||
| − | Bus Interface: PCI |
||
| − | Slot: 1 |
||
| − | Serial Number: PACCR9SYRIHU |
||
| − | Cache Serial Number: PAAVP9SYYM4C |
||
| − | RAID 6 (ADG) Status: Disabled |
||
| − | Controller Status: OK |
||
| − | Hardware Revision: C |
||
| − | Firmware Version: 6.64 |
||
| − | Wait for Cache Room: Disabled |
||
| − | Surface Analysis Inconsistency Notification: Disabled |
||
| − | Post Prompt Timeout: 0 secs |
||
| − | Cache Board Present: True |
||
| − | Cache Status: Not Configured |
||
| − | Drive Write Cache: Disabled |
||
| − | Total Cache Size: 512 MB |
||
| − | Total Cache Memory Available: 400 MB |
||
| − | No-Battery Write Cache: Disabled |
||
| − | Battery/Capacitor Count: 0 |
||
| − | SATA NCQ Supported: True |
||
| − | |||
| − | |||
| − | |||
| − | unassigned |
||
| − | |||
| − | physicaldrive 2I:1:3 |
||
| − | Port: 2I |
||
| − | Box: 1 |
||
| − | Bay: 3 |
||
| − | Status: OK |
||
| − | Drive Type: Unassigned Drive |
||
| − | Interface Type: SAS |
||
| − | Size: 300 GB |
||
| − | Rotational Speed: 10000 |
||
| − | Firmware Revision: HPD7 |
||
| − | Serial Number: 6XP5CLK80000B335CPL7 |
||
| − | Model: HP EG0300FBLSE |
||
| − | PHY Count: 2 |
||
| − | PHY Transfer Rate: 6.0Gbps, Unknown |
||
| − | |||
| − | |||
| − | SEP (Vendor ID PMCSIERA, Model SRC 8x6G) 250 |
||
| − | Device Number: 250 |
||
| − | Firmware Version: RevC |
||
| − | WWID: 5001438006116C2F |
||
| − | Vendor ID: PMCSIERA |
||
| − | Model: SRC 8x6G |
||
| − | </PRE> |
||
| − | }} |
||
| − | |||
| − | ==Статус контроллера== |
||
| − | <PRE> |
||
| − | hpacucli ctrl all show status |
||
| − | |||
| − | Smart Array P410 in Slot 1 |
||
| − | Controller Status: OK |
||
| − | Cache Status: Not Configured |
||
| − | </PRE> |
||
| − | |||
| − | ==Управление кэшированием== |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 modify dwc=disable |
||
| − | |||
| − | Error: This operation is not supported with the current configuration. Use the |
||
| − | "show" command on devices to show additional details about the |
||
| − | configuration. |
||
| − | Reason: Controller not configured |
||
| − | </PRE> |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 modify dwc=enable |
||
| − | |||
| − | Warning: Without the proper safety precautions, use of write cache on physical |
||
| − | drives could cause data loss in the event of power failure. To ensure |
||
| − | data is properly protected, use redundant power supplies and |
||
| − | Uninterruptible Power Supplies. Also, if you have multiple storage |
||
| − | enclosures, all data should be mirrored across them. Use of this |
||
| − | feature is not recommended unless these precautions are followed. |
||
| − | Continue? (y/n) |
||
| − | </PRE> |
||
| − | |||
| − | У меня не включился, думаю из-за |
||
| − | <PRE> |
||
| − | Battery/Capacitor Count: 0 |
||
| − | </PRE> |
||
| − | |||
| − | ==Пересканировать устройства== |
||
| − | Пересканировать устройства, добавленные с момента последнего сканирования |
||
| − | <PRE> |
||
| − | hpacucli rescandetects newly added devices since the last rescan |
||
| − | </PRE> |
||
| − | В моем случае ни к чему не привело - диск нашелся сам по себе |
||
| − | |||
| − | ==Просмотр информации по отдельному диску == |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 pd 2I:1:3 show detail |
||
| − | </PRE> |
||
| − | <PRE> |
||
| − | Smart Array P410 in Slot 1 |
||
| − | |||
| − | unassigned |
||
| − | |||
| − | physicaldrive 2I:1:3 |
||
| − | Port: 2I |
||
| − | Box: 1 |
||
| − | Bay: 3 |
||
| − | Status: OK |
||
| − | Drive Type: Unassigned Drive |
||
| − | Interface Type: SAS |
||
| − | Size: 300 GB |
||
| − | Rotational Speed: 10000 |
||
| − | Firmware Revision: HPD7 |
||
| − | Serial Number: 6XP5CLK80000B335CPL7 |
||
| − | Model: HP EG0300FBLSE |
||
| − | PHY Count: 2 |
||
| − | PHY Transfer Rate: 6.0Gbps, Unknown |
||
| − | </PRE> |
||
| − | |||
| − | Во многих примерах приводят <code>pd 2:3 </code> (2-х значный адрес) вместо <code>pd 2I:1:3</code> (3-х значный), возможно связано с версией контроллера или утилит. |
||
| − | <BR> |
||
| − | Сам адрес диска, если он не известен можно посмотреть в <code> hpacucli ctrl all show config detail </code> |
||
| − | <PRE> |
||
| − | physicaldrive 2I:1:3 |
||
| − | Port: 2I |
||
| − | Box: 1 |
||
| − | Bay: 3 |
||
| − | </PRE> |
||
| − | |||
| − | ==Статус дисков== |
||
| − | |||
| − | Все диски |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 pd all show status |
||
| − | physicaldrive 2I:1:3 (port 2I:box 1:bay 3, 300 GB): OK |
||
| − | </PRE> |
||
| − | Или отдельный диск (а он тут всего один) |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 pd 2I:1:3 show status |
||
| − | physicaldrive 2I:1:3 (port 2I:box 1:bay 3, 300 GB): OK |
||
| − | </PRE> |
||
| − | |||
| − | |||
| − | ==Очистка== |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 pd 2I:1:3 modify erase |
||
| − | </PRE> |
||
| − | |||
| − | ==Управление диодами на дисках== |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 pd 2I:1:3 modify led=on |
||
| − | </PRE> |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 pd 2I:1:3 modify led=off |
||
| − | </PRE> |
||
| − | |||
| − | ==Показать информацию (детально)== |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 ld all show detail |
||
| − | |||
| − | Error: The specified device does not have any logical drives. |
||
| − | </PRE> |
||
| − | Логических дисков пока нет |
||
| − | |||
| − | ==Создание дисков== |
||
| − | логический диск (отдельный диск). Команда не возвращает вывод, результат смотреть отдельно. |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 create type=ld drives=2I:1:3 raid=0 |
||
| − | </PRE> |
||
| − | |||
| − | Просмотреть что вышло? |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=1 ld all show detail |
||
| − | |||
| − | Smart Array P410 in Slot 1 |
||
| − | |||
| − | array A |
||
| − | |||
| − | Logical Drive: 1 |
||
| − | Size: 279.4 GB |
||
| − | Fault Tolerance: 0 |
||
| − | Heads: 255 |
||
| − | Sectors Per Track: 32 |
||
| − | Cylinders: 65535 |
||
| − | Strip Size: 256 KB |
||
| − | Full Stripe Size: 256 KB |
||
| − | Status: OK |
||
| − | Caching: Enabled |
||
| − | Unique Identifier: 600508B1001C8823B6E46FDAC58243EC |
||
| − | Disk Name: /dev/sdb |
||
| − | Mount Points: None |
||
| − | Logical Drive Label: A7044617PACCR9SYRIHUC7C6 |
||
| − | Drive Type: Data |
||
| − | </PRE> |
||
| − | <PRE> |
||
| − | dmesg -T | tail -10 |
||
| − | [Sun Sep 3 11:34:03 2023] loop7: detected capacity change from 0 to 8 |
||
| − | [Sun Sep 3 16:36:18 2023] hpsa 0000:09:00.0: scsi 6:0:2:0: masked Direct-Access HP EG0300FBLSE PHYS DRV SSDSmartPathCap- En- Exp=0 |
||
| − | [Mon Sep 4 08:48:25 2023] hpsa 0000:09:00.0: scsi 6:1:0:0: added Direct-Access HP LOGICAL VOLUME RAID-0 SSDSmartPathCap- En- Exp=1 |
||
| − | [Mon Sep 4 08:48:25 2023] scsi 6:1:0:0: Direct-Access HP LOGICAL VOLUME 6.64 PQ: 0 ANSI: 5 |
||
| − | [Mon Sep 4 08:48:25 2023] sd 6:1:0:0: [sdb] 585871964 512-byte logical blocks: (300 GB/279 GiB) |
||
| − | [Mon Sep 4 08:48:25 2023] sd 6:1:0:0: [sdb] Write Protect is off |
||
| − | [Mon Sep 4 08:48:25 2023] sd 6:1:0:0: [sdb] Mode Sense: 6b 00 00 08 |
||
| − | [Mon Sep 4 08:48:25 2023] sd 6:1:0:0: Attached scsi generic sg2 type 0 |
||
| − | [Mon Sep 4 08:48:25 2023] sd 6:1:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA |
||
| − | [Mon Sep 4 08:48:25 2023] sd 6:1:0:0: [sdb] Attached SCSI disk |
||
| − | </PRE> |
||
| − | |||
| − | ==Примеры из интерента которые не проверял== |
||
| − | |||
| − | |||
| − | ===логический диск — чередование=== |
||
| − | <PRE> |
||
| − | hpacucli> ctrl slot=0 create type=ld drives=1:13,1:14 size=300 raid=1 |
||
| − | </PRE> |
||
| − | ===логический диск — raid 5=== |
||
| − | <PRE> |
||
| − | hpacucli> ctrl slot=0 create type=ld drives=1:13,1:14,1:15,1:16,1:17 raid=5drives — конкретные диски, все диски (all drives) или неиспользуемые диски (unassigned drives) |
||
| − | </PRE> |
||
| − | size -размер логического диска в Мб |
||
| − | raid — тип raid 0, 1 , 1+0 and 5 |
||
| − | |||
| − | |||
| − | ===Удаление=== |
||
| − | <PRE> |
||
| − | hpacucli> ctrl slot=0 ld 4 delete |
||
| − | </PRE> |
||
| − | |||
| − | ===Добавление дисков=== |
||
| − | <PRE> |
||
| − | hpacucli> ctrl slot=0 ld 4 add drives=2:3 |
||
| − | </PRE> |
||
| − | |||
| − | ===Добавление дискового пространства (принудительно)=== |
||
| − | <PRE> |
||
| − | hpacucli ctrl slot=0 ld 4 modify size=500 forced |
||
| − | </PRE> |
||
| − | ===Добавление резервного диска spare=== |
||
| − | <PRE> |
||
| − | hpacucli> ctrl slot=0 array all add spares=1:5,1:7 |
||
| − | </PRE> |
||
=<code>smartctl</code>= |
=<code>smartctl</code>= |
||
Версия 11:45, 7 сентября 2023
Raid на серверах HP
Мне достались 2 сервера с разными контроллерами
- H410 с кешем и P240 без кеша
|
|
|
|---|---|
lspci -s 09:00.0 -vv 09:00.0 RAID bus controller: Hewlett-Packard Company Smart Array G6 controllers (rev 01) Subsystem: Hewlett-Packard Company Smart Array P410 |
lspci -s 06:00.0 -vv 06:00.0 RAID bus controller: Hewlett-Packard Company Smart Array Gen9 Controllers (rev 01) Subsystem: Hewlett-Packard Company H240 |
09:00.0 RAID bus controller: Hewlett-Packard Company Smart Array G6 controllers (rev 01) Subsystem: Hewlett-Packard Company Smart Array P410 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Interrupt: pin A routed to IRQ 37 Region 0: Memory at fbc00000 (64-bit, non-prefetchable) [size=2M] Region 2: Memory at fbbff000 (64-bit, non-prefetchable) [size=4K] Region 4: I/O ports at d800 [size=256] Expansion ROM at fbb00000 [disabled] [size=512K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: CorrErr- NonFatalErr+ FatalErr+ UnsupReq- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM not supported ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s (ok), Width x8 (ok) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ NROPrPrP- LTR- 10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp- ExtTPHComp- AtomicOpsCap: 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [ac] MSI-X: Enable+ Count=16 Masked- Vector table: BAR=0 offset=001c2000 PBA: BAR=0 offset=001c4000 Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Kernel driver in use: hpsa Kernel modules: hpsa |
lspci -s 06:00.0 -vv 06:00.0 RAID bus controller: Hewlett-Packard Company Smart Array Gen9 Controllers (rev 01) Subsystem: Hewlett-Packard Company H240 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Interrupt: pin A routed to IRQ 57 Region 0: Memory at fbd00000 (64-bit, non-prefetchable) [size=1M] Region 2: Memory at fbcffc00 (64-bit, non-prefetchable) [size=1K] Region 4: I/O ports at d800 [size=256] Expansion ROM at fbc00000 [disabled] [size=512K] Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] MSI: Enable- Count=1/32 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [b0] MSI-X: Enable+ Count=64 Masked- Vector table: BAR=0 offset=00002000 PBA: BAR=0 offset=00003000 Capabilities: [c0] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <1us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: CorrErr- NonFatalErr+ FatalErr+ UnsupReq- RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 8GT/s, Width x8, ASPM not supported ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s (downgraded), Width x8 (ok) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range B, TimeoutDis+ NROPrPrP- LTR- 10BitTagComp- 10BitTagReq- OBFF Via message, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp+ ExtTPHComp- AtomicOpsCap: 32bit+ 64bit+ 128bitCAS+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkCap2: Supported Link Speeds: 2.5-8GT/s, Crosslink- Retimer- 2Retimers- DRS- LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Capabilities: [300 v1] Secondary PCI Express LnkCtl3: LnkEquIntrruptEn- PerformEqu- LaneErrStat: 0 Kernel driver in use: hpsa Kernel modules: hpsa |
|
Модуль ядра: |
Модуль ядра: |
smartctl
- В части
-d cciss,00 - это номер диска (а так как их в логическом устройстве всего один, то номер у него нулевой). Для более сложных рейдов будут доступны и другие значения.
smartctl -x /dev/sdb -d cciss,0 --all
